Enterprise Wi-Fi Installation and Wireless Network Optimization
We design Wi-Fi based on the building plan, user density and the devices used on site. After installation, we measure coverage, channel use and roaming between access points in the real areas of use.
More than signal strength
The signal level a device shows doesn’t by itself indicate capacity or connection stability.
The whole wireless network, from planning to measurement
Building materials, user density, device types and applications’ roaming behavior determine not only the number of access points but also their placement and the radio plan.
RF plan
Balance of channels, bands and power
Coverage
Site measurement and weak area analysis
Capacity
Client density and airtime assessment
Security
Corporate SSID, 802.1X and guest separation
Coverage isn’t enough; capacity must be planned too
60 devices in a meeting room can generate more traffic than the devices across an entire warehouse. That’s why planning is based on user density and applications.
Signal and noise
For areas where voice and video calls are used, −67 dBm is a commonly used example design target; it isn’t an acceptance threshold for every device and application. When setting the target we also take into account the signal-to-noise ratio (SNR) and the capabilities of client devices.
Channel plan
At 2.4 GHz, 1, 6 and 11 are a common channel plan for a 20 MHz channel width. The choice is made according to national rules and interference on site. 5 GHz has more channels; in dense environments a 20 or 40 MHz channel width is preferred.
Transmit power
Turning power up to the maximum may not solve a coverage problem; it can cause clients to stay connected to a distant access point.
Building structure
Reinforced concrete walls, glass partitions, elevator shafts and metal racks attenuate the signal to different degrees; planning calculates by material.
We design for the real usage scenario
The number and placement of access points are determined not by square meters but by user density, applications and building structure. After installation, coverage and channel distribution are verified by site measurement.
Site survey
Environmental effects such as walls, racks, production areas and channel interference are identified. Warehouse and production sites using handheld terminals and vehicle-mounted computers fall within the scope of our industrial wireless network service. If the wireless need is a link carrying video traffic, a wireless IP camera and point-to-point bridge solution is assessed separately.
RF optimization
2.4/5/6 GHz suitability, channel width, transmit power and interaction with neighboring APs are assessed.
Roaming and identity
Roaming, 802.1X/RADIUS, guest access and application interruptions are tested.
Wi-Fi 6, 6E and 7: which one, where?
The benefit of newer standards appears only if client devices support them too. Use of the 6 GHz band depends on national regulations and device support; these conditions are verified separately in the planning phase.
| Standard | Bands | Key feature |
|---|---|---|
| Wi-Fi 6 (802.11ax) | 2.4 / 5 GHz | More efficient channel use in dense environments with OFDMA |
| Wi-Fi 6E | 2.4 / 5 / 6 GHz | Additional channel options at 6 GHz; requires client support and national regulation |
| Wi-Fi 7 (802.11be) | 2.4 / 5 / 6 GHz | Multi-link operation (MLO); 320 MHz channel width only at 6 GHz, if device support and national regulations allow |
802.11k helps find neighboring access points. 802.11v can pass a roaming suggestion to the client. 802.11r can shorten authentication time during roaming on compatible clients. The client makes the roaming decision. These features are tested with the devices on site. In security, the roles are separate: WPA3 defines encryption and key management for the wireless connection; 802.1X ensures the user or device is authenticated before being admitted to the network; RADIUS is the server that performs this authentication. A separate SSID and VLAN are used for guests.
What will you have at the end of the wireless network work?
A coverage map verified by site measurement, an access point placement plan, SSID and security configuration, and a record of channel/power settings.
A documented, verifiable result
AP placement and coverage plan
SSID/VLAN and authentication matrix
Channel/power configuration record
Site acceptance and roaming test results
Let’s clarify a detail
If your question is specific to your network, write to us; we’ll look at the current setup and give you a clear answer.
Does moving to Wi-Fi 7 solve every problem?
No. RF design, client support, the wired uplink, channel density and the authentication infrastructure are decisive.
Why does our wireless network slow down in certain areas?
Possible causes include channel overlap, excessively high transmit power, clients on older standards consuming channel airtime, and the access point’s uplink capacity. We determine which one is in play by site measurement.
Can an enterprise wireless network be built with consumer access points?
It can work for a small area. We make the comparison based on device features and management needs: central management, coordinated channel and power tuning, 802.11k/v/r and 802.1X support vary by model. As the number of users and access points grows, the need for these features grows too.
Do you measure after installation?
Yes. After installation, coverage, signal levels and channel distribution are verified with a site measurement; the results are reported on the building plan.
Related network services
The wireless network is planned together with the cabling, segmentation and device installation work below.
Enterprise Switch and Router Installation
Installation of managed switches, routers and firewalls; redundant, documented configuration.
Enterprise VLAN Setup and Network Segmentation
802.1Q, inter-VLAN routing, access rules and secure network segmentation.
Network Performance Analysis and Troubleshooting
Identifying slowness, drops and packet loss by measurement, and fixing them permanently.
All network services
See the full list of services.
Contact Us
Go to the request and contact form.
On the systems side, with Server and Cloud Management, 802.1X authentication on the wireless network is tied to the Active Directory and RADIUS infrastructure.
Vendor-specific wireless deployments: HPE Aruba, Ubiquiti UniFi and MikroTik CAPsMAN.
Knowledge Center
Technical guides for this service
Let’s plan your wireless network with measurement
Share your building plan and user density; let’s decide the number and placement of access points by measurement.
We deliver wireless network projects across Türkiye; coverage measurement and access point installation are done on site, while monitoring and tuning are done remotely. Our service areas.