Network and IP Planning · #14

Online Fiber Optic Link Budget Calculator

Calculates received power and remaining margin from transmitter power, fiber and connection losses.

  • Data is processed in your browser and not sent to a server

Tool

Minimum Tx from the data sheet.

Rx sensitivity from the data sheet.

Rx overload / maximum input power.

dB/km

Each patch panel pass counts as one pair.

Typically 0.3–0.5 dB; TIA-568 maximum 0.75 dB.

Typically 0.1 dB; TIA-568 maximum 0.3 dB.

For ageing, repair splices and contamination.

What does this tool do?

An SFP's 'reach' assumes ideal fiber and few connections. Real links add patch panel connectors, fusion splices and older fiber. The tool sums the loss in dB, calculates the received power in dBm and the margin against the receiver sensitivity, and shows whether short links overload the receiver.

How to use it

  1. Enter the transmitter's minimum output power and the receiver sensitivity in dBm from the data sheet; add the overload value if known.
  2. Enter the length in km and fiber attenuation in dB/km (single-mode 1310 nm ≈ 0.35; 1550 nm ≈ 0.25; multimode 850 nm ≈ 3.0–3.5).
  3. Enter connector and splice counts, their loss and the safety margin you want.

Fields

Transmit power (minimum)
Minimum Tx from the data sheet.
Receiver sensitivity
Rx sensitivity from the data sheet.
Receiver overload (optional)
Rx overload / maximum input power.
Link length
Fiber attenuation
dB/km
Connector pairs
Each patch panel pass counts as one pair.
Loss per connector
Typically 0.3–0.5 dB; TIA-568 maximum 0.75 dB.
Fusion splices
Loss per splice
Typically 0.1 dB; TIA-568 maximum 0.3 dB.
Safety margin
For ageing, repair splices and contamination.

Worked example

InputValue
Transmit power (minimum)-3
Receiver sensitivity-12
Link length10
Fiber attenuation0.35
Connector pairs1
Loss per connector0.5
Fusion splices0
Loss per splice0.1
Safety margin3

Expected result: Loss 3.5 + 0.5 = 4 dB; received power −3 − 4 = −7 dBm; 5 dB raw margin against −12 dBm sensitivity, 2 dB after a 3 dB margin.

dBm is absolute power, dB is a ratio: you add losses in dB and subtract them from dBm. 5 dB raw margin means the link works; 2 dB left after the safety margin can absorb another patch pass (≈0.5 dB) and one repair splice.

Second scenario

InputValue
Transmit power (minimum)-1
Receiver sensitivity-14.4
Receiver overload (optional)0.5
Link length0.3
Fiber attenuation3.5
Connector pairs2
Loss per connector0.5
Fusion splices0
Loss per splice0.1
Safety margin3

Expected result: On a 300 m multimode link the loss is 2.05 dB and received power −3.05 dBm; below the +0.5 dBm overload limit, so no attenuator is needed. Raw margin 11.35 dB, 8.35 dB after the safety margin.

Method and assumptions

Total loss (dB) = km × dB/km + connectors × connector loss + splices × splice loss. Received power (dBm) = Tx (dBm) − loss (dB). Raw margin (dB) = received power − sensitivity. Net margin = raw margin − safety margin.

If received power exceeds the receiver overload limit, an attenuator of at least the difference is needed; this usually happens when long-reach SFPs are used on short links.

Using the result and troubleshooting

A negative net margin calls for a stronger SFP, fewer connection points or better fiber. Verify the real loss with an OTDR or optical power meter; the tool gives a planning value.

When troubleshooting, clean connectors first: one dirty connector alone can add more than 1 dB.

Limits and common mistakes

  • Dispersion, multimode bandwidth-distance and wavelength-dependent loss differences are not calculated.
  • Enter the minimum, not the typical transmit power; the typical value overstates the margin.

Frequently asked questions

What is the difference between dB and dBm?

dBm is absolute power relative to 1 mW (0 dBm = 1 mW). dB is a ratio between two powers. −3 dBm minus 4 dB loss gives −7 dBm.

Related tools and service

Related service: Structured Cabling and Low-Voltage Infrastructure

Network online tools · See all online tools