Network and IP Planning · #15

Online Wi-Fi Channel Plan Draft

Drafts a channel plan that spreads neighbouring APs across channels and shows remaining conflicts clearly.

  • Data is processed in your browser and not sent to a server
  • Export: CSV

Tool

At 40/80 MHz only standard bonded groups fully inside the permitted list are used.

Comma-separated primary 20 MHz channel numbers.

One per line: AP name; neighbouring APs that hear it (comma-separated).

What does this tool do?

Neighbouring APs on the same channel share airtime and wait for each other (co-channel contention). A channel plan gives APs that hear each other different channels. The tool drafts an assignment from the neighbour relationships you enter and the channels you have verified as permitted in your country. It is not a site survey.

How to use it

  1. Choose band and channel width. Only 20 MHz is supported on 2.4 GHz.
  2. List usable channels (e.g. 1,6,11 for 2.4 GHz; 36,40,44,48,52,... for 5 GHz). Verify the country regulations and DFS use yourself.
  3. Write AP; neighbour1,neighbour2 on each line. Neighbourhood is two-way; write it once.

Fields

Band
Channel width
At 40/80 MHz only standard bonded groups fully inside the permitted list are used.
Permitted channels
Comma-separated primary 20 MHz channel numbers.
APs and neighbours
One per line: AP name; neighbouring APs that hear it (comma-separated).

Worked example

InputValue
Band2.4 GHz
Channel width20 MHz
Permitted channels1,6,11
APs and neighbours
AP-1;AP-2,AP-3
AP-2;AP-3
AP-3

Expected result: AP-1 → 1, AP-2 → 6, AP-3 → 11; no conflict.

Three APs hear each other and 2.4 GHz has three non-overlapping channels, so each gets its own. Add a fourth neighbouring AP and at least two share a channel; the tool marks it yellow and leaves the decision to lower power or move to 5 GHz to you.

Second scenario

InputValue
Band5 GHz
Channel width40 MHz
Permitted channels36,40,44,48
APs and neighbours
AP-1;AP-2,AP-3
AP-2;AP-3
AP-3;AP-4
AP-4

Expected result: At 40 MHz only the groups 36+40 and 44+48 exist: AP-1 and AP-4 get 44+48; AP-2 and AP-3, which hear each other, share 36+40 and are marked yellow.

Four channels become only two groups at 40 MHz. Three APs that hear each other do not fit in two groups; dropping to 20 MHz or adding DFS channels resolves the conflict.

Method and assumptions

APs and neighbours form a graph; channel assignment is graph colouring. The DSatur heuristic is used: the AP with the most differently-coloured neighbours goes first, ties go to the AP with most neighbours, and the least-used suitable channel is chosen.

At 40 and 80 MHz the standard 5 GHz bonding groups (36-40, 44-48, …; 36-48, 52-64, …) are used; every channel of a group must be in the permitted list. On 2.4 GHz entered channels must be at least 5 channels apart (non-overlapping).

When colours run out, the heuristic tries to minimise conflicts; it does not prove a conflict is theoretically unavoidable.

Using the result and troubleshooting

When entering the draft into the WLAN controller, validate it with site survey measurements. Taking neighbours from the controller's RF neighbour report is more accurate than estimating.

Common fixes for remaining conflicts: lower AP power, narrow the channel width or disable the 2.4 GHz radio on some APs.

Limits and common mistakes

  • Country regulations are not applied; you enter the permitted channels. DFS channels being vacated on radar detection is not considered.
  • Signal strength, wall attenuation and coverage are not calculated; only channels are assigned.
  • The 6 GHz band is not included in this version.

Frequently asked questions

Why only 1, 6 and 11 on 2.4 GHz?

20 MHz channels are 5 MHz apart and about 22 MHz wide; channels closer than 5 apart overlap. In most regions only 1, 6 and 11 do not.

Related tools and service

Related service: Wireless Network Installation and Optimization

Network online tools · See all online tools