Network and IP Planning · #14
Online Fiber Optic Link Budget Calculator
Calculates received power and remaining margin from transmitter power, fiber and connection losses.
- Data is processed in your browser and not sent to a server
Tool
What does this tool do?
An SFP's 'reach' assumes ideal fiber and few connections. Real links add patch panel connectors, fusion splices and older fiber. The tool sums the loss in dB, calculates the received power in dBm and the margin against the receiver sensitivity, and shows whether short links overload the receiver.
How to use it
- Enter the transmitter's minimum output power and the receiver sensitivity in dBm from the data sheet; add the overload value if known.
- Enter the length in km and fiber attenuation in dB/km (single-mode 1310 nm ≈ 0.35; 1550 nm ≈ 0.25; multimode 850 nm ≈ 3.0–3.5).
- Enter connector and splice counts, their loss and the safety margin you want.
Fields
- Transmit power (minimum)
- Minimum Tx from the data sheet.
- Receiver sensitivity
- Rx sensitivity from the data sheet.
- Receiver overload (optional)
- Rx overload / maximum input power.
- Link length
- Fiber attenuation
- dB/km
- Connector pairs
- Each patch panel pass counts as one pair.
- Loss per connector
- Typically 0.3–0.5 dB; TIA-568 maximum 0.75 dB.
- Fusion splices
- Loss per splice
- Typically 0.1 dB; TIA-568 maximum 0.3 dB.
- Safety margin
- For ageing, repair splices and contamination.
Worked example
| Input | Value |
|---|---|
| Transmit power (minimum) | -3 |
| Receiver sensitivity | -12 |
| Link length | 10 |
| Fiber attenuation | 0.35 |
| Connector pairs | 1 |
| Loss per connector | 0.5 |
| Fusion splices | 0 |
| Loss per splice | 0.1 |
| Safety margin | 3 |
Expected result: Loss 3.5 + 0.5 = 4 dB; received power −3 − 4 = −7 dBm; 5 dB raw margin against −12 dBm sensitivity, 2 dB after a 3 dB margin.
dBm is absolute power, dB is a ratio: you add losses in dB and subtract them from dBm. 5 dB raw margin means the link works; 2 dB left after the safety margin can absorb another patch pass (≈0.5 dB) and one repair splice.
Second scenario
| Input | Value |
|---|---|
| Transmit power (minimum) | -1 |
| Receiver sensitivity | -14.4 |
| Receiver overload (optional) | 0.5 |
| Link length | 0.3 |
| Fiber attenuation | 3.5 |
| Connector pairs | 2 |
| Loss per connector | 0.5 |
| Fusion splices | 0 |
| Loss per splice | 0.1 |
| Safety margin | 3 |
Expected result: On a 300 m multimode link the loss is 2.05 dB and received power −3.05 dBm; below the +0.5 dBm overload limit, so no attenuator is needed. Raw margin 11.35 dB, 8.35 dB after the safety margin.
Method and assumptions
Total loss (dB) = km × dB/km + connectors × connector loss + splices × splice loss. Received power (dBm) = Tx (dBm) − loss (dB). Raw margin (dB) = received power − sensitivity. Net margin = raw margin − safety margin.
If received power exceeds the receiver overload limit, an attenuator of at least the difference is needed; this usually happens when long-reach SFPs are used on short links.
Using the result and troubleshooting
A negative net margin calls for a stronger SFP, fewer connection points or better fiber. Verify the real loss with an OTDR or optical power meter; the tool gives a planning value.
When troubleshooting, clean connectors first: one dirty connector alone can add more than 1 dB.
Limits and common mistakes
- Dispersion, multimode bandwidth-distance and wavelength-dependent loss differences are not calculated.
- Enter the minimum, not the typical transmit power; the typical value overstates the margin.
Frequently asked questions
What is the difference between dB and dBm?
dBm is absolute power relative to 1 mW (0 dBm = 1 mW). dB is a ratio between two powers. −3 dBm minus 4 dB loss gives −7 dBm.
Related tools and service
- Structured Cabling Quantity CalculatorTurns a cabling survey into a bill of materials: boxes, panels, patch cords and jacks.
Related service: Structured Cabling and Low-Voltage Infrastructure